Digital to Analog Converter Manufacturer,Supplier and Exporter in India
Product Code : EL-DET-1516
Jlab Export is a leading Digital to Analog Converter Manufacturer,and suppliers in India
Digital to Analog Converter (code EL-DET-1516) is a self-contained training board for studying the basic principle of digital to analog conversion. Students set a 4-bit digital input on switches, hold it in a storage register, and read the resulting analog output directly as a voltage on a built-in voltmeter; the conversion uses a binary weighted ladder network. It is made by Jain Laboratory Instruments Pvt Ltd (JLab) at its works in Ambala, India.
Specifications
| Parameter | Detail |
|---|---|
| Experiment | Basic principle of digital to analog conversion |
| Digital input word length | 4 bits |
| Input switches and indicators | Four switches for binary logic input states; four LEDs showing the input status |
| Input storage register | 4 D-type flip-flops |
| D/A mode | Binary weighted ladder network |
| Other circuit blocks | Four level amplifiers |
| Analog signal variation | 0 to +5 V |
| Analog display | DC voltmeter, 65 mm rectangular dial, 0–5 V with linear calibration; continuous monitoring of the analog output |
| Built-in supplies | +5 V DC at 250 mA (IC regulated), +10 V DC at 50 mA and −10 V DC at 50 mA, all internally connected |
| Mains controls | Mains ON/OFF switch, fuse and jewel light |
| Supply required | 230 V ±10% at 50 Hz AC mains |
| Patch cords | Adequate number; stackable from the rear at both ends; 4 mm spring-loaded plugs; length ½ metre (0.5 m) |
| Panel terminals | Terminals and sockets on the panel for connections and observation of waveforms |
| Operating instructions | Detailed instructions giving the object, theory, design procedures, report suggestions and book references |
| Quality check | Each board is visually inspected before dispatch |
| Pack quantity | Each (sold individually) |
| Minimum order quantity | 10 units |
| Dispatch time | Usually 7–10 working days |
| Product code | EL-DET-1516 |
| Manufacturer | Jain Laboratory Instruments Pvt Ltd (JLab) — OEM |
| Country of origin | India (made in Ambala, Haryana) |
How Does It Compare with the JLab 8-Bit Multiplying DAC?
| Board | Digital input | Conversion | Built-in DC supplies | Output reading |
|---|---|---|---|---|
| Digital to Analog Converter (EL-DET-1516) | 4 bits, set on four switches and held in a 4 D-type flip-flop register | Binary weighted ladder network | +5 V, +10 V and −10 V | Built-in 0–5 V voltmeter; requires no other apparatus |
| 8-Bit Multiplying Digital to Analog Converter | 8 bits, set on SPDT switches | 8-bit D to A converter with an op-amp; output represents the product of the inputs and a reference source | ±15 V and +5 V | A 3¾-digit digital multimeter is the other apparatus required |
This 4-bit board makes the ladder-network principle easy to follow on a meter of its own, while the 8-bit multiplying board shows how a converter IC produces an output proportional to both the digital input and the reference.
What Is the Digital to Analog Converter Board Used For?
A digital to analog converter turns a binary number into a proportional voltage, the step that lets digital systems drive meters, motors, audio stages and control signals. In an ideal converter the output rises by one equal step each time the binary count goes up by one, and in a 4-bit word the most significant bit carries eight times the weight of the least significant. With the voltmeter on the output, students can note the reading for every input code and plot output against input to see how closely the steps follow a straight line.
What to Specify When Ordering
- Resolution — this 4-bit ladder-network board, or the 8-bit multiplying digital to analog converter.
- Quantity — the number of boards for your digital electronics lab.
- Companion boards — the analog to digital converter and the other trainers listed below are separate boards that can go on the same enquiry.
Frequently Asked Questions
How does a binary weighted ladder network convert the input?
Each bit of the digital word switches a contribution into the network that is weighted by its binary place value, and the network adds these contributions together. The output voltage is therefore proportional to the binary number set on the input switches.
Why does the board have a storage register?
The four D-type flip-flops each store one bit, so the input word set on the switches is held steady at the converter’s input while the output is read. This is how a converter is fed in a real digital system, where data arrives and is latched before conversion.
What output range does the board give?
The analog output varies from 0 to +5 V and is read on a 0–5 V voltmeter with linear calibration. With 4 input bits there are sixteen output levels.
Is any other instrument needed?
No. The board is self contained and requires no other apparatus; it runs from 230 V ±10%, 50 Hz AC mains and has its own DC supplies and voltmeter.
What information is needed for an export quotation?
Send the number of boards, the destination country and port or city, your preferred delivery terms (for example FOB or CIF), any packing or labelling requirements, and the tender reference if the purchase is for a tender.
Who manufactures the Digital to Analog Converter board?
Jain Laboratory Instruments Pvt Ltd, trading as JLab, manufactures it at its works in Ambala, Haryana, India, and quotes for it directly.
OEM Manufacturer
JLab is the trading name of Jain Laboratory Instruments Pvt Ltd, an electronics trainer and laboratory equipment manufacturer in India, incorporated in 2017 and based on Hargolal Road, Ambala, Haryana. This D/A converter board is built at JLab’s own works rather than bought from a trader, so engineering colleges, polytechnics, dealers and importers buy it factory-direct, every board is visually inspected before dispatch, and repeat orders and spares are handled by the manufacturer. JLab holds MSME Udyam registration UDYAM-HR-01-0003849 as a manufacturing enterprise and is registered for export under Importer-Exporter Code 3317504552. JLab exports worldwide and ships to buyers in every region — for example Bulgaria in Eastern Europe, Ireland in Western Europe, Kazakhstan in Central Asia, Trinidad and Tobago in Central America and the Caribbean, and Australia in Oceania. Tender details are on the JLab lab tenders page.
Related Converter and Logic Trainers
- 8-Bit Multiplying Digital to Analog Converter — an 8-bit converter whose output represents the product of the digital input and a reference source.
- Analog to Digital Converter — the opposite conversion: a 0 to +15 V input turned into a 4-bit word on seven-segment displays.
- Training Board of Flip Flops — for constructing D, J-K, T and RS flip-flops like those used in the input register.
- Binary to Decimal Encoder — shows a 4-bit binary code as a decimal digit on a seven-segment display.
See the complete Digital Electronics Trainer range or all Electronics Lab Equipments.
Request a Quote
Add this board to an enquiry with the Add To Cart button, or contact JLab through the contact page with the quantity, the delivery destination and any converter or logic boards you want quoted alongside it.
Last updated: 22 October 2026
