Analog to Digital Converter Manufacturer,Supplier and Exporter in India
Product Code : EL-DET-1515
Jlab Export is a leading Analog to Digital Converter Manufacturer,and suppliers in India
Analog to Digital Converter (code EL-DET-1515) is a self-contained training board for studying the basic principle of converting an analog signal into a digital one and the working of a digital voltmeter. An input varied from 0 to +15 V is converted into a 4-bit word and shown as 0 to 15 on seven-segment displays. It is made by Jain Laboratory Instruments Pvt Ltd (JLab) at its works in Ambala, India.
Specifications
| Parameter | Detail |
|---|---|
| Experiments | Basic principle of conversion of an analog signal to a digital signal; working of a digital voltmeter |
| Analog signal variation | 0 to +15 V |
| Digital word length | 4 bits |
| Decoder display | 0 to 15, on seven-segment displays |
| Built-in fixed supplies | +5 V DC at 250 mA, −5 V DC at 50 mA and +10 V DC at 50 mA, IC regulated, internally connected |
| Variable supply | 0–15 V DC at 50 mA, continuously variable |
| Analog meter | DC voltmeter, 65 mm rectangular dial, reading 0–15 V |
| Conversion and logic ICs | Voltage comparator; quad 2-input NAND gate; quad 2-input NOR gate; quad 2-input AND gate; dual 4-input AND gate; quad 2-input EX-OR gate; three hex buffer/drivers; BCD-to-7-segment decoder/driver; dual J-K flip-flop; 4-bit binary ripple counter; timer |
| Clock | Internal clock, with provision for manual pulses |
| Monitoring | Analog signals on the voltmeter and digital signals on the 7-segment display, continuously |
| Indicators | Seven LEDs showing the state of important points (LED on for ‘1’, off for ‘0’); two seven-segment displays for the output status |
| Mains controls | Mains ON/OFF switch, fuse and jewel light |
| Supply required | 230 V ±10% at 50 Hz AC mains |
| Patch cords | Adequate number; stackable from the rear at both ends; 4 mm spring-loaded plugs; length ½ metre (0.5 m) |
| Panel terminals | Terminals and sockets on the panel for connections and observation of waveforms |
| Operating instructions | Detailed instructions with the object, theory, design procedures, report suggestions and book references |
| Quality check | Each board is visually inspected before dispatch |
| Pack quantity | Each (sold individually) |
| Minimum order quantity | 10 units |
| Dispatch time | Usually 7–10 working days |
| Product code | EL-DET-1515 |
| Manufacturer | Jain Laboratory Instruments Pvt Ltd (JLab) — OEM |
| Country of origin | India (made in Ambala, Haryana) |
How Does It Compare with the JLab 8-Bit Analog to Digital Converter?
| Board | Digital output | Built-in DC supplies | Main conversion parts | Readout and other apparatus |
|---|---|---|---|---|
| Analog to Digital Converter (EL-DET-1515) | 4 bits | +5 V, −5 V, +10 V and a 0–15 V variable supply | Voltage comparator, 4-bit binary ripple counter, timer and logic gates | Built-in voltmeter, seven-segment displays and LEDs; requires no other apparatus |
| 8-Bit Analog to Digital Converter | 8 bits | ±5 V DC at 50 mA | A to D converter IC working by successive approximation, timer IC and buffer IC | LEDs for status; a 3¾-digit digital multimeter is the other apparatus required |
The 4-bit board shows the conversion principle and the digital voltmeter with its own meter, displays and variable source, while the 8-bit board demonstrates successive-approximation conversion to an 8-bit word with an A to D converter IC and an external digital multimeter.
What Is the Analog to Digital Converter Board Used For?
An analog to digital converter turns a continuously variable voltage into a binary number, which is how digital instruments, data loggers and computers take in readings from the real world. On this board the analog side is watched on the voltmeter and the digital side on the LEDs and seven-segment display at the same time, so students can see how each change of input voltage becomes a new binary code. Because a digital voltmeter is essentially a converter followed by a decoder and display, the board also shows how such a meter arrives at the figure it shows.
What to Specify When Ordering
- Resolution — this 4-bit board for the conversion principle and the digital voltmeter, or the 8-bit successive-approximation board for higher-resolution work.
- Quantity — the number of boards for your electronics lab.
- Companion boards — the digital to analog converter and the other trainers listed below are separate items that can be quoted on the same enquiry.
Frequently Asked Questions
What resolution does a 4-bit converter give?
A 4-bit word has sixteen possible codes (two to the power four), so the 0 to +15 V input range is represented by the values 0 to 15 on the display. More bits give finer steps, as on the 8-bit board.
Does the board need an external meter or other apparatus?
No. It is self contained and requires no other apparatus: the analog input is read on its own DC voltmeter with a 65 mm rectangular dial, and the digital result on its seven-segment displays.
What do the LEDs show?
Seven LEDs show the state of important points in the circuit. Each LED glows for a ‘1’ state and is off for a ‘0’ state, so students can follow the binary value while the conversion runs.
What mains supply does it use?
230 V ±10% at 50 Hz AC. All the DC supplies for the circuits, including the 0–15 V variable source, are built in.
What information is needed for an export quotation?
Please give the number of boards, the destination country and port or city, your delivery terms (such as FOB or CIF), any packing or labelling needs, and a tender reference where there is one.
Who manufactures this ADC trainer?
JLab — Jain Laboratory Instruments Pvt Ltd — makes it at its works in Ambala, Haryana, India, and quotes for it directly.
OEM Manufacturer
JLab is the trading name of Jain Laboratory Instruments Pvt Ltd, an Indian manufacturer of electronics training boards and laboratory equipment, incorporated in 2017 and based on Hargolal Road, Ambala, Haryana. The analog to digital converter board comes from JLab’s own works rather than from a trading house, so colleges, institutes, dealers and importers buy it factory-direct; each board is visually inspected before it is packed, and repeat orders and spare parts are handled by the manufacturer. JLab exports worldwide and ships to buyers in every region — for example Ukraine in Eastern Europe, the Netherlands in Western Europe, DR Congo in Central Africa, Algeria in North Africa and Kyrgyzstan in Central Asia. Tender information is on the JLab lab tenders page.
Related Converter and Logic Trainers
- 8-Bit Analog to Digital Converter — successive-approximation conversion of an analog signal to an 8-bit word.
- Digital to Analog Converter — the reverse process: a 4-bit input stored in a register and converted by a binary weighted ladder network, read on a voltmeter.
- Binary to Decimal Encoder — a BCD-to-7-segment decoder/driver that shows a 4-bit binary code as a decimal digit.
- Logic Training Board on Counters and Shift Registers — ripple, synchronous, ring and Johnson counters and shift registers.
See the complete Digital Electronics Trainer range or all Electronics Lab Equipments.
Request a Quote
To get a quotation, click Add To Cart and submit the enquiry, or write through the contact page with the number of boards, the delivery address or port, and any other converter or logic trainers you would like included.
Last updated: 22 October 2026
