Ratchet Tube Bender Kit Manufacturer,Supplier and Exporter in India
Product Code : EL-AELE-12908
Jlab Export is a leading Ratchet Tube Bender Kit Manufacturer,and suppliers in India
This kit holds the tools to cut, clean and bend soft copper tube for refrigeration and air conditioning work. A ratchet bender with four bender heads forms 1/4, 5/16, 3/8 and 1/2 in OD tube. A heavy-duty tube cutter and an inner-outer reamer come with it, and everything packs into a moulded case.
Specifications
| Tube sizes | 1/4, 5/16, 3/8 and 1/2 in OD |
| Suitable for | Copper pipe |
| Bender | 1 ratchet bender |
| Bender heads | 4 |
| Tube cutter | Heavy duty, for 1/8 to 1 1/8 in OD tubing |
| Reamer | Inner-outer, for 3/16 to 1 1/2 in OD tubing |
| Case | Moulded case |
| Minimum order quantity | 10 units |
| Dispatch time | Usually 4–6 working days |
| Manufacturer | JLab (Jain Laboratory Instruments Pvt Ltd), Ambala, India |
Workshop Practice with the Bender Kit
A first RAC workshop job is to cut, ream and bend one length of soft copper tube. Students cut it square with the kit’s cutter, tightening the wheel a little on each turn. The reamer then takes the burr out of the bore so the tube keeps its full flow area. With the matching head fitted, they make a right-angle bend, an offset and a U-bend. Each one is then checked for flats or ripples on the inside of the curve.
Teachers can set out one bend made three ways. The first comes from this ratchet bender, the second from a Spring Tube Bender, and the third by hand with a Bending Spring inside 1/2 in tube. The bent pieces then go to the Hydraulic Flaring And Swaging Tool Kit for a flare or a socket, and the sockets are joined with Brazing Rod.
Frequently Asked Questions
Which tube sizes can the ratchet bender handle?
It bends 1/4, 5/16, 3/8 and 1/2 in OD copper tube, with four bender heads in the kit. Fit the head that matches the outside diameter of the tube. A head that is too large leaves the wall unsupported and lets it flatten.
Why choose a ratchet bender over a long lever bender?
The ratchet handle turns the head in short strokes, so you do not need room to swing a long lever. That helps when a bend has to be made on tube already in place inside a unit or close to a wall.
Can the cutter and reamer work on bigger tube than the bender takes?
Yes. The heavy-duty cutter takes tubing from 1/8 to 1 1/8 in OD, and the reamer works on 3/16 to 1 1/2 in OD. Both serve larger lines that are joined by brazing rather than bent with this kit.
How do I check a right-angle bend?
Lay the bent tube on a flat bench and set a try square against both legs. Then measure from the tube end to the centre line of the other leg and compare it with the drawing. Move the next bend mark if the length is out.
How do I keep copper tube from kinking in the bender?
Use soft, annealed copper and the head that fits it. Pull the handle in steady strokes and stop at the angle you need, since going back over a bend weakens the wall. Hard-drawn tube should be annealed at the bend first.
Other Tube Bending and Cutting Tools
- Lever Type Tube Bender (lever bender with a red angle scale)
- Copper Pipe Bender (five metric tube and conduit sizes)
- Eccentric Flaring Tool
- Tube Cutter (heavy duty, aluminium body)
For a quote, use Add To Cart or send us a message through the contact page.
Last updated: 5 November 2026
