Electro Pneumatic Trainer Manufacturer,Supplier and Exporter in India
Product Code : EL-CTM-9063
Jlab Export is a leading Electro Pneumatic Trainer Manufacturer,and suppliers in India
Electrical signals switch the air on this trainer. Panel switches, a 24 V DC relay module and inductive proximity sensors drive 5/2 and 3/2 way solenoid valves. The valves move a single-acting cylinder, a double-acting cylinder and an air motor. Students wire the control side on the panel and pipe the air side with push-pull tubing.
Specifications
| Cylinders | Single acting and double acting, 25 mm bore x 100 mm stroke, foot mounted |
| Solenoid valves | 2 nos: 5/2 way and 3/2 way, 1/4 in, 230 V AC or 24 V DC |
| Logic and flow valves | AND (dual pressure) valve, OR (shuttle) valve, flow control valve, non-return valve, all 1/4 in |
| Air preparation | AFR/FRL unit, 1/4 in, 0–10 kg/cm² |
| Air distribution | 6-way block manifold, sintered silencer, male connectors, push-pull connectors |
| Sensors | Inductive proximity, 2-wire, 18 mm diameter, 5 mm sensing distance |
| Pressure gauge | 0–7 kg/cm², 100 mm dial, 1/2 in BSP |
| Air motor | Unidirectional, 22,000 rpm free speed, 0–90 psi |
| Electrical panel | Powder-coated MS panel with switches, 24 V DC indicator lamps, test points and controller, DIN-rail terminals, 24 V DC relay module with 2 NO/NC contacts |
| Tubing and compressor | 6 mm OD / 4 mm ID tube, 10 m clear and 10 m blue, optional 25 litre, 2 CFM, 2 HP compressor working at 5–6 kg/cm² |
| Minimum order quantity | 1 unit |
| Dispatch time | Usually 14–18 working days |
| Manufacturer | JLab (Jain Laboratory Instruments Pvt Ltd), Ambala, India |
Electro-Pneumatic Practicals
The first circuits use direct control. A switch energises the 3/2 way solenoid valve and the single-acting cylinder extends, then springs back when the switch is released. The 5/2 way valve does the same for the double-acting cylinder. Students then build a latching relay circuit that keeps the cylinder out after the switch is let go. A proximity sensor at the end of stroke then brings it back.
The AND valve gives an output only when both inputs carry air, which is the basis of a two-hand start. The shuttle valve passes air from either input, so a cylinder can be worked from two places. Air comes from the optional compressor or a workshop Air Compressor, and the inside of each valve type can be shown on Transparent Pneumatic Components. A Digital Multimeter checks the 24 V DC supply at the test points.
Frequently Asked Questions
What air supply does the trainer need?
It works from a compressed-air supply that the FRL unit filters and regulates, with the gauge reading 0–7 kg/cm². The optional compressor has a 25 litre tank, delivers 2 CFM and works at 5–6 kg/cm² from a 2 HP, 230 V AC motor.
Which coil voltages do the solenoid valves use?
The 5/2 way and 3/2 way valves are offered for 230 V AC or 24 V DC. The panel lamps and the relay module run on 24 V DC, which keeps the control wiring at low voltage.
What do the proximity sensors detect?
They are inductive sensors, so they sense metal without touching it, up to 5 mm away. The 2-wire sensor has an 18 mm body and is placed where the moving part should stop, to signal the end position.
Does the trainer use relays or a PLC?
Control on this trainer is by relay board logic, built from the 24 V DC relay module with 2 NO/NC contacts. Students who move on to programmable control can continue on the PLC and HMI Training Kit.
How fast does the air motor run?
The unidirectional air motor has a free speed of 22,000 rpm and works on air from 0 to 90 psi. Students can slow it with the flow control valve to see how air flow sets motor speed.
Other Pneumatic and Hydraulic Trainers
- Advanced Electro Pneumatic Trainer
- Pneumatic Trainer
- Electro Hydraulic Trainer
- Hydraulic Trainer Kit
For a quote, use Add To Cart or send us a message through the contact page.
Last updated: 6 November 2026
