• +91-85699-09696

CNC Training Mill, VMC with Rigid Tapping Manufacturer,Supplier and Exporter in India

CNC Training Mill, VMC with Rigid Tapping

Product Code : EL-CTM-9040
Jlab Export is a leading CNC Training Mill, VMC with Rigid Tapping Manufacturer,and suppliers in India

This vertical machining centre carries a 20-tool magazine with a double gripper tool changer and an 8,000 rpm spindle on a box-structured base and column. A screw-type side chip conveyor with a built-in external coolant system clears chips from the table during long cycles. Through-spindle coolant is a separate option. Rigid tapping is standard, so threaded holes can be cut in the same set-up as the milling.

Specifications

Machine typeVertical machining centre (VMC)
Base and columnBox-structured
Spindle speed8,000 rpm standard, 10,000 rpm optional
Tool magazine20 tools, double gripper automatic tool changer
Chips and coolantScrew-type side chip conveyor with built-in external coolant system, coolant tank and pump with chip tray
Through-spindle coolantOption, quoted separately from the external coolant system
TappingRigid tapping
Lights and levellingWork light, pilot light, levelling bolts and pads
ManualsOperating manual and programming manual
Options4th axis CNC rotary table, 7/9 kW spindle motor, voltage stabiliser or isolation transformer, tooling and fixtures to suit the job
Minimum order quantity1 unit
Dispatch timeUsually 14–18 working days
ManufacturerJLab (Jain Laboratory Instruments Pvt Ltd), Ambala, India

Workshop Practice on the Machining Centre

A typical first job is a plate with a pocket, a profile and a few tapped holes. Students write the part program in G-code and M-code, using G00 for rapid moves, G01 for straight feeds and G02 or G03 for arcs. They run it in simulation, set the work offset on the clamped blank and measure each tool’s length offset before cutting.

After machining, they check pocket widths with a Dial Caliper and the plate thickness with an External Micrometer. A Dial Gauge on its magnetic base shows whether the milled face is flat. Teachers can then change one feed or speed in the program and let the class compare the surface finish.

Frequently Asked Questions

What spindle speed does this machine run at?
The standard spindle runs to 8,000 rpm. A 10,000 rpm spindle and a 7/9 kW spindle motor are offered as options. Higher speeds suit small cutters and soft metals such as aluminium, where a small tool needs more revolutions to reach its cutting speed.

How does the double gripper tool changer work?
The changer arm has a gripper at each end. It pulls the tool out of the spindle and the next tool out of the 20-tool magazine at the same moment, swaps them and swings back. This keeps the idle time between cuts short.

What is rigid tapping?
In rigid tapping the control locks spindle rotation to the Z-axis feed, so the tap advances one pitch for every turn. The spindle then reverses to back the tap out. No floating tap holder is needed, and holes can be tapped straight after drilling.

Can a fourth axis be added?
Yes. A 4th axis CNC rotary table is offered as an option. It turns the work under program control, so flats, cross holes and slots around a part can be cut without unclamping and resetting it.

What should be arranged on site before installation?
The machine stands on levelling bolts and pads, so it needs a firm, level floor. Where the mains supply varies, a voltage stabiliser or isolation transformer can be ordered with it. Tooling and fixtures can be supplied to suit the parts the institute plans to make.

Other Machining Centres and CNC Mills

For a quote, use Add To Cart or send us a message through the contact page.

Last updated: 20 November 2026


   

Office Address

Works: 2475-84,
Hargolal Road,Ambala, Haryana

[email protected]

+91-85699-09696

Follow Us